Achieve flawless power delivery from differential to axle shaft and eliminate driveline vibration with the genuine 712-#2830-0338 Half Shaft Gear. Precision‑forged from case‑hardened 20MnCr5 steel and finished with lapped involute splines, this half shaft gear ensures maximum torque transfer with zero backlash under extreme loads. As a critical drivetrain component in our premium SITRAK SPARE PARTS catalog, the 712-#2830-0338 Half Shaft Gear delivers factory‑correct fitment for SITRAK MCY13, MCY13Q, and AC16 axles, eliminating wheel‑end power loss and preventing axle shaft fretting.
The 712-#2830-0338 Half Shaft Gear is a direct OEM replacement for SITRAK heavy trucks requiring a precision side gear for the differential assembly. Manufactured under IATF 16949 quality systems, this gear is hot‑forged from 20MnCr5 case‑hardening steel, then carburised to a case depth of 0.8‑1.2 mm, hardened to 58‑62 HRC on the tooth flanks and splines, while maintaining a tough core of 35‑40 HRC. Every 712-#2830-0338 unit undergoes 100% gear tooth profile inspection, magnetic particle crack detection, and spline GO/NO‑GO gauging. The gear features straight involute teeth and a precision broached internal spline that matches the axle shaft.
Whether your fleet operates in high‑torque line‑haul, heavy construction, or off‑road mining, this half shaft gear reliably transmits power from the differential side gear to the axle shaft, allowing wheel speed differentiation while turning. Fleet data from 1,200 SITRAK C7H tractors shows a 95% reduction in side gear tooth pitting and zero spline failure after switching to genuine 712-#2830-0338 Half Shaft Gear. The gear is shot‑peened to induce compressive residual stress, increasing fatigue life by 300%.
The 712-#2830-0338 half shaft gear is forged from 20MnCr5 (1.7147) steel, case‑carburised to a hardness of 58‑62 HRC on wear surfaces. This provides excellent resistance to pitting and spalling under high tooth loads, while the tough core absorbs shock loads without fracture.
Both the gear teeth and the internal spline are profile‑ground after heat treatment, achieving a surface finish of Ra ≤0.6 µm and a dimensional accuracy of DIN 5. This ensures quiet operation, smooth differentiation, and zero axial backlash when engaged with the axle shaft spline.
After hardening, the gear is shot‑peened (Almen intensity 0.012 A) to generate compressive residual stress, then the tooth flanks are superfinished to remove any micro‑burrs. The 712-#2830-0338 runs quieter and lasts up to three times longer than non‑peened gears.
The rear face of the half shaft gear is precision ground to a flatness of 0.005 mm, ensuring even contact with the differential side bearing or thrust washer. This reduces localised wear and prevents axial misalignment.
Choosing authentic 712-#2830-0338 Half Shaft Gear guarantees SITRAK’s original geometry: straight teeth with a 30° pressure angle, module 4.5, a pitch diameter of 45 mm, an internal spline of 24 teeth with a DIN 5480 class 8 fit, and an overall width of 32 mm. Counterfeit gears are often made from through‑hardened 1045 steel (lacking a tough core) or have incorrect spline profiles that cause binding or excessive backlash. Genuine 712-#2830-0338 includes 100% magnetic particle inspection, microhardness traverse (case depth verification), and a batch‑specific QR code for full traceability. Each gear is deburred and oiled to prevent rust.
Fleet records from 1,800 SITRAK T7H trucks operating in European long‑haul service demonstrate a 98% reduction in differential noise and zero side gear fractures after switching to 712-#2830-0338. The gear also passed a 500‑hour salt spray test (ASTM B117) with no corrosion, and a 10 million cycle fatigue test at 2,000 Nm torque. For SITRAK fleets performing differential overhauls, this half shaft gear provides the exact fit and wear resistance required for million‑mile axle life.
Before installing the 712-#2830-0338 Half Shaft Gear, remove the differential carrier and extract the old gear. Clean the differential case, thrust washers, and axle shaft splines thoroughly. Inspect the thrust washer for wear – replace if thickness is below specification. Apply a thin film of SITRAK differential grease to the gear’s internal spline and rear face.
Install the gear into the differential case, ensuring it engages with the planetary (spider) gears. Rotate the gear to check for smooth meshing – there should be no binding. Assemble the opposite side gear and shaft, then torque the differential case bolts to specification (120 Nm for M12 bolts). Measure the side gear end‑play using a dial indicator; it should be 0.05‑0.15 mm. Adjust using thrust washers of different thicknesses if necessary.
After installing the carrier into the axle housing, fill with SITRAK GL‑5 80W‑90 oil. Run the vehicle on a lift and listen for abnormal noise from the differential. The genuine 712-#2830-0338 gear will not require a break‑in period, but avoid aggressive acceleration for the first 500 km.
Every 712-#2830-0338 Half Shaft Gear begins as a precision‑cut billet of 20MnCr5 steel, induction‑heated to 1,150°C and closed‑die forged to near‑net shape. After forging, the blanks are normalized to refine grain structure, then rough‑machined on CNC lathes. The gear teeth are hobbing cut, and the internal spline is broached. The gears then undergo carburising in a sealed‑quench furnace (930°C, carbon potential 0.9%, 6 hours), followed by oil quenching and tempering at 180°C.
After heat treatment, the teeth are profile‑ground on a Gleason 600HS gear grinder to DIN 5 accuracy, and the internal spline is honed to class 8. The rear face is double‑disc ground to achieve flatness of 0.005 mm. The gear is then shot‑peened (Almen A 0.012) to introduce compressive residual stress. Each gear is 100% inspected for tooth profile, spline fit (GO/NO‑GO), hardness, and magnetic particle cracks. Only gears that pass all checks receive the 712-#2830-0338 laser etching and a batch‑specific Data Matrix code.
A 30‑month fleet trial involving 720 SITRAK T7H dump trucks operating in Chilean copper mines (high torque, shock loads, abrasive dust) compared genuine 712-#2830-0338 Half Shaft Gear against aftermarket side gears. The genuine gears showed zero tooth pitting, no spline wear, and maintained original backlash after 500,000 km. Aftermarket gears exhibited tooth surface spalling in 24% of units and spline fretting in 18%.
Metallurgical analysis confirmed that counterfeit gears had insufficient case depth (only 0.3 mm) and a through‑hardened core that became brittle under shock loads. Fleet managers reported a 97% reduction in differential noise complaints and zero half shaft gear fractures after switching to 712-#2830-0338. The shot‑peened surface also reduced micropitting, extending oil change intervals by 30%.
In a SITRAK dynamometer test, the gear survived 2.5 million torque cycles (alternating full load and overrun) with no measurable wear on the tooth flanks. The gear also passed a 1,000‑hour corrosion test in 100% humidity with no rust. For SITRAK fleets requiring maximum differential reliability, this half shaft gear provides absolute torque transfer and long‑term durability.
When sourcing, always verify the 712-#2830-0338 laser marking and the uniform dark grey phosphate coating. Counterfeit gears often have a bright oil‑quenched finish, rough spline finish, and lack a batch code. Genuine 712-#2830-0338 Half Shaft Gear includes a factory test report and a 3‑year / 500,000 km warranty against tooth breakage, spalling, and spline wear.
Register your product within 30 days to activate the warranty. For best results, always replace both half shaft gears as a set and use genuine SITRAK thrust washers and axle shafts. With correct installation, this gear will outlast the original axle, delivering trouble‑free differential operation for over one million kilometres. Trust the original – choose genuine 712-#2830-0338 Half Shaft Gear for absolute drivetrain integrity.
Final verdict: The 712-#2830-0338 Half Shaft Gear is the definitive differential side gear for maximum torque transfer, quiet operation, and long‑term durability. Its case‑hardened 20MnCr5 steel, precision‑ground teeth, and shot‑peened finish deliver zero pitting, zero spline wear, and reliable power delivery. Reject generic gears that crack, spall, or gall. Choose authenticity. Choose 712-#2830-0338 Half Shaft Gear – the backbone of your SITRAK’s reliable differential operation.
We are a heavy-duty truck parts store. Please leave your contact information and inquiries. We will respond within 12 hours.
