The Motor Starting wire is the essential high-current cable that delivers battery power directly to the starter motor, ensuring reliable engine cranking on the HOWO A7 8X4. This comprehensive kit includes the main Starting Motor wire harness, Plastic Fix belt ties, multiple Ring spacers, and large quantities of Wire sheath protective sleeving. When you choose genuine howo Parts for your Motor Starting wire replacement, you guarantee minimal voltage drop, maximum cranking power, and long-lasting protection against chafing, heat, and abrasion.
The Starting Motor wire is a heavy-gauge cable that connects the battery positive terminal to the starter solenoid. It is designed to handle the extremely high inrush current required to crank a large diesel engine.
This cable is constructed with finely stranded copper conductors and a thick, heat-resistant PVC jacket. It is rated for continuous duty at temperatures up to 105°C, ensuring reliable performance even after repeated hot starts.
The cable length is optimized for the HOWO A7 8X4 chassis, with a 3100mm routing that reaches from the battery box to the starter mounted on the engine bell housing. The terminals are pre-crimped and soldered for maximum conductivity.
Over time, the original Motor Starting wire can develop internal corrosion or insulation damage, leading to voltage drop and slow cranking. Replacing it with a new cable restores full starting power and reduces strain on the starter.
The Plastic Fix belt is a rugged cable tie used to secure the Motor Starting wire along the chassis and engine components. It is made from UV-stabilized nylon 6/6 with a length of 200mm and width of 8mm.
These belts provide strong tensile strength and resist loosening under vibration, ensuring the cable remains securely routed and protected from chafing against sharp edges.
Three fix belts are included in the kit, sufficient to secure the cable at strategic intervals along its route, maintaining a tidy and safe installation.
The Ring is a specialized spacer or isolating component used to maintain proper clearance between the Motor Starting wire and the chassis. It prevents direct contact with sharp metal edges that could cut the insulation.
Two part numbers are offered: WG9100360314 and 199100360134, both serving the same purpose but with slight dimensional differences to suit different mounting locations.
These rings are made from durable, non-conductive material that resists heat, oil, and abrasion. They are essential for maintaining cable integrity and preventing short circuits.
The Wire sheath is a flexible protective sleeve that encases the Motor Starting wire, shielding it from mechanical damage, heat, and moisture. It is made from flame-retardant, abrasion-resistant material.
Three part numbers are supplied: 190003179046 (150 pieces), 190003179044 (150 pieces), and additional quantities for complete coverage. Each sheath piece is 125mm long and can be cut to length as needed.
The sheath is slit longitudinally for easy installation over the cable, and it can be secured with tape or ties. It provides an extra layer of defense against chafing and abrasion, especially where the cable passes through frame holes or near moving parts.
For the Motor Starting wire system, using wire sheath is highly recommended to extend cable life and prevent costly electrical failures. The kit includes ample sheathing to cover the entire length of the cable.
Motor Starting wire – Complete starter cable, fix belts, rings, and wire sheath for HOWO A7 8X4
| Part NO. | Description |
|---|---|
| AZ9721778207 | Starting Motor wire |
| WG9003171393 | Plastic Fix belt |
| WG9100360314 | Ring |
| 199100360134 | Ring |
| 190003179046 | Wire sheath |
| 190003179046 | Wire sheath |
| 190003179044 | Wire sheath |
| 190003179044 | Wire sheath |
Our Motor Starting wire is manufactured with premium-grade copper and heavy-duty insulation, ensuring the lowest possible resistance and maximum current delivery. This translates to faster, more reliable engine starts even in extreme cold.
The included wire sheath, fix belts, and rings provide comprehensive protection against chafing, heat, and vibration. This extends the service life of the cable and reduces the risk of electrical fires or starter failure.
Our kit is designed for a perfect fit on the HOWO A7 8X4, with pre-cut cable length and all necessary hardware. Installation is straightforward, saving you time and ensuring a professional result.
We supply genuine howo Parts, guaranteed to meet or exceed OEM specifications. Choose our Motor Starting wire for reliable starting performance and peace of mind, backed by our comprehensive warranty.
The Motor Starting wire is the lifeline of the starting system. It must carry currents exceeding 1000 amperes during cranking, which means even a small increase in resistance can drastically reduce cranking speed.
Common causes of poor starting include corroded cable ends, internal wire breakage, and damaged insulation that allows moisture ingress. Replacing the entire Motor Starting wire is often the most reliable solution.
The wire sheath and rings are not optional accessories; they are critical for preventing chafing that could lead to a short circuit. A short in the starter cable can drain the battery and even cause a fire.
Using plastic fix belts to secure the cable ensures that it does not droop onto hot exhaust parts or moving suspension components, which would quickly damage the insulation.
Before installation, always disconnect both battery terminals. Remove the old cable and inspect the mounting points for any damage or corrosion that should be cleaned before fitting the new cable.
Route the new Motor Starting wire along the original path, using the plastic fix belts to secure it to the frame at intervals of about 300mm. Apply the rings at points where the cable passes through frame holes.
Slide the wire sheath over the cable before making terminal connections. Cut the sheath to the required length and secure it with tape or additional ties to prevent it from sliding.
Attach the cable ends to the battery and starter terminals, torquing the nuts to the manufacturer’s specification (typically 20–25 N·m). Apply a thin layer of dielectric grease to the terminals to prevent corrosion.
After installation, reconnect the battery and test the starter. Listen for a strong, fast crank. Check for any signs of heating at the cable ends after a prolonged crank – this indicates a poor connection.
The Motor Starting wire (AZ9721778207) is specifically designed for the HOWO A7 8X4 with the 3100mm routing length. It fits all engine variants offered in this model.
The plastic fix belts, rings, and wire sheath are universal components that can be used on any cable of similar diameter. They are included for convenience and quality assurance.
If your vehicle has a different battery or starter location, you may need a custom-length cable. Our technical support team can assist in selecting the correct part for your specific application.
Always verify the cable gauge and terminal sizes before ordering to ensure compatibility with your existing starter and battery terminals.
A properly installed Motor Starting wire ensures that your truck starts reliably every time, reducing the risk of being stranded with a dead battery or failed starter.
The heavy-duty construction and protective sheathing mean this cable will last for years, even in harsh environments with salt, mud, and extreme temperatures.
By using genuine parts, you avoid the common issue of cheap aftermarket cables that have inadequate copper strands, leading to overheating and fire risk.
For fleet operators, standardizing on our Motor Starting wire kit simplifies maintenance and ensures consistent starting performance across the entire fleet.
We recommend inspecting the starter cable during every oil change – look for cracks in the insulation, loose terminals, or signs of chafing. Replace the cable if any damage is found.
Our technical team is available to provide installation guidance and answer any questions about the Motor Starting wire system. We are committed to keeping your HOWO A7 8X4 running smoothly.
Order your Motor Starting wire kit today and enjoy the confidence that comes with a reliable starting system. Your truck’s performance depends on it.
We offer competitive pricing and fast shipping to minimize your downtime. Keep your fleet moving with genuine howo Parts for all your electrical needs.
Remember to use the wire sheath on any section of the Motor Starting wire that runs near sharp edges or high-heat areas. This simple step greatly extends cable life.
For any questions about installation or compatibility, our support team is just an email away. We are here to ensure you get the most out of your Motor Starting wire investment.
Our online catalog provides comprehensive access to genuine SINOTRUK parts for all major vehicle lines — including HOWO, Sitrak, Steyr, and Yellow River series trucks. You can browse detailed specifications, original part numbers, and exploded-view diagrams for every assembly. Whether you are performing routine maintenance or planning a major overhaul, the catalog helps you quickly identify the correct components for your vehicle. When you become a SINOTRUK customer, we offer complimentary full‑access catalog services, ensuring you always have the latest product data and interchangeability information at your fingertips to support efficient fleet management and accurate parts ordering.
We are a heavy-duty truck parts store. Please leave your contact information and inquiries. We will respond within 12 hours.
