| No. | Part No. | Name |
|---|---|---|
| 1 | Q402B05 | Big washer |
| 2 | AZ1630110176 | Circular buffer block |
| 3 | Q32006 | Hexagon flange nut M6 |
| 4 | Q40306 | Spring washer |
| 5 | ZQ1840620 | Hexagon bolt with flange M6 |
| 6 | ZQ1840625 | Hexagon toothed bolt with flange M6 |
| 7 | Q502014 | Cutter pin |
| 8 | Q2714813F31 | Cross-recessed pan head tapping screw |
| 9 | WG1642110014 | Hinge support assembly |
| 10 | WG1642110016 | Hinge base |
| 11 | WG1642110017 | Hinge pin |
| 12 | Q40008 | Small washer |
| 13 | WG1642930003 | Blanking cap |
| 14 | WG1642110022 | Plastic rivets for fixing A column |
| 15 | WG1642111048 | Mask limit block right bracket assembly |
| 16 | WG9100360134 | Spacer ring |
| 17 | WG1642111021 | Door lower left hinge cover |
| 18 | WG1642111022 | Door lower right hinge cover |
| 19 | 810-96805-0000 | Drawstring |
| 20 | WG1642111011 | 10 radiator mask |
| 21 | WG1642111013 | Left wind hood |
| 22 | WG1642111014 | Right wind scooter |
| 23 | WG1642111023 | Door left upper hinge cover |
| 24 | WG1642111015 | Mask net (I) |
| 25 | WG1642111016 | Mask net (II) |
| 26 | WG1642111017 | Left side screen |
| 27 | WG1642111018 | Right guard |
| 28 | WG1642110032 | Left hinge welding assembly |
| 29 | WG1644110006 | SNOTRUK big design trademark (Plated silver) |
| 30 | WG1642110033 | Right hinge welding assembly |
| 31 | WG1642110019 | Left A column trim panel |
| 32 | WG1642110020 | Right A column trim panel |
| 33 | WG1642111024 | Door upper right hinge cover |
| 34 | WG1642111027 | Mask skeleton |
| 35 | WG1642110021 | Left A pillar fixing clip |
| 36 | WG1642110041 | Right A-pillar fixing clip |
| 37 | ZQ1840816 | Hexagon bolt with flange M8 |
| 38 | WG1642110027 | Mask right lock assembly |
| 39 | WG1642110028 | Mask left lock assembly |
| 40 | WG1642110018 | Protection bar |
| 41 | WG1642111030 | 10 HOWO gas spring support bolts |
| 42 | WG1646110001 | Water fender |
| 43 | WG9918580037 | RFID electronic tag |
| 44 | WG1642111047 | Mask limit block left bracket assembly |
| 45 | WG1642931001 | Left trim panel |
| 46 | WG1642931002 | Right trim panel |
The Big washer is a large‑diameter flat washer used to distribute clamping load over a wide area, protecting the panel surfaces from damage. It is used under bolt heads and nuts in the front shroud and radiator cover assembly, ensuring a secure and stable connection that resists loosening under vibration.
The Circular buffer block is a rubber damping element that absorbs shocks and reduces vibration between the mask and the chassis. It also acts as a spacer to maintain correct alignment of the front shroud and radiator cover components, preventing rattling and metal‑to‑metal contact.
The Hexagon flange nut M6 is a self‑locking nut with an integrated flange that provides a wide bearing surface, eliminating the need for a separate washer. It is used with M6 bolts to secure lightweight components in the front shroud and radiator cover, offering a reliable, vibration‑proof fastening.
The Spring washer is a split‑ring lock washer that provides tension to prevent fasteners from loosening under vibration. It is used in critical joints of the front shroud and radiator cover assembly, ensuring that bolts and nuts remain securely tightened over the life of the vehicle.
The Hexagon bolt with flange M6 is a high‑strength fastener with an integrated flange that eliminates the need for a washer. It is used for attaching trim panels and covers, providing a secure and corrosion‑resistant connection in the front shroud and radiator cover.
This bolt features a toothed flange that bites into the mating surface, providing a positive locking action. It is used in high‑vibration areas of the front shroud and radiator cover, ensuring that the fasteners remain tight and secure.
The Cutter pin is a split pin used to secure hinge pins and other removable fasteners, preventing them from working loose. Its spring‑steel construction allows easy installation and removal, making it ideal for maintenance.
This self‑tapping screw features a cross‑recessed pan head, designed for fastening plastic and thin metal components without the need for pre‑drilling. It is used extensively in the front shroud and radiator cover for attaching trims and nets.
The Hinge support assembly is a robust bracket that holds the mask hinges, providing a stable pivot point for the radiator cover. It is manufactured from heavy‑gauge steel with anti‑corrosion coating, ensuring long‑term durability.
The Hinge base is the fixed plate that attaches to the chassis, providing a mounting point for the hinge pin and support assembly. It is precision‑drilled for accurate alignment.
The Hinge pin is a hardened steel pivot pin that connects the hinge support to the base, allowing the mask to open and close smoothly. Its precise diameter ensures a tight fit and minimal play.
The Small washer is a compact flat washer used in confined spaces where a larger washer would not fit. It provides adequate load distribution for lighter fasteners in the front shroud and radiator cover assembly.
The Blanking cap is a decorative cover that fills unused holes in the mask or trim, providing a clean, finished appearance. It is made from UV‑stabilised plastic to resist fading and cracking.
These plastic rivets are used to secure the A‑column trim panels without damaging the paint. They expand upon insertion, providing a secure, vibration‑resistant hold that is easy to remove for servicing.
This bracket assembly limits the opening travel of the mask on the right side, preventing over‑extension and protecting the hinges. It is a key safety component of the front shroud and radiator cover.
The Spacer ring is a precision‑machined metal ring used to maintain correct clearance between components, ensuring that the mask sits flush and operates smoothly.
This trim cover conceals the lower left door hinge, providing a neat appearance and protecting the hinge mechanism from dirt. It is made from impact‑resistant plastic that matches the cab interior.
Symmetrical with the left part, this cover hides the lower right door hinge, maintaining a uniform interior appearance. Both covers are interchangeable for ease of service.
The Drawstring is a flexible cable or strap used to operate the mask lock mechanism from inside the cab, allowing the driver to open the radiator cover easily.
The 10 radiator mask is the main grille panel that covers the radiator and provides a distinctive front‑end style. It is manufactured from high‑impact polymer with a chrome‑or silver‑finish option.
The Left wind hood is an aerodynamic panel that directs airflow over the left side of the engine bay, improving cooling efficiency and reducing drag.
Symmetrical with the left part, the Right wind scooter guides airflow on the right side. Both components are essential for proper radiator cooling in the front shroud and radiator cover system.
This cover hides the upper left door hinge, completing the interior trim. It is colour‑matched to the cab interior and provides a clean finish.
The Mask net (I) is an upper grille mesh that provides a stylish appearance while protecting the radiator from large debris. Its open design ensures unrestricted airflow.
The lower grille mesh, complementing Mask net (I), fills the lower opening of the mask. Both nets are interchangeable and are made from durable polymer.
The Left side screen is a decorative mesh insert on the left side of the mask, adding a sporty touch while allowing air to pass through.
Symmetrical with the left part, the Right guard is a protective mesh that shields the right side of the radiator from stones and debris.
This welded steel assembly forms the left hinge structure, providing a robust pivot point for the mask. It is precision‑welded for strength and alignment.
This is the official SNOTRUK brand emblem, plated in silver for a premium look. It is mounted on the front mask, signifying genuine quality and origin.
Symmetrical with the left, this welded assembly supports the right hinge, ensuring balanced opening and closing of the mask.
The Left A column trim panel covers the structural pillar on the driver side, providing a finished interior and housing for wiring and airbag modules.
Symmetrical with the left, this panel covers the passenger‑side A‑pillar, completing the cab interior trim.
This cover hides the upper right door hinge, providing a consistent look across all door hinge covers.
The Mask skeleton is the internal structural frame that gives the mask rigidity and supports the grille and emblem. It is made from high‑strength polymer for lightweight strength.
This clip secures the left A‑pillar trim panel, ensuring it stays firmly attached without rattling. It is easy to install and remove.
Symmetrical to the left, this clip secures the right A‑pillar trim panel, providing identical retention force.
The M8 flange bolt is a larger fastener used for heavier connections, such as mounting the mask skeleton and hinges. Its flange provides a wide bearing surface.
This assembly includes the latch and striker for the right side of the mask, securely holding the cover closed. It is spring‑loaded for smooth operation.
Symmetrical with the right, this assembly locks the left side of the mask. Both locks work in tandem to secure the cover.
The Protection bar is a steel reinforcement that shields the radiator from frontal impacts, adding an extra layer of safety.
These bolts are used to attach the gas springs that assist in lifting the mask. They are made from hardened steel and are plated for corrosion resistance.
The Water fender is a splash guard that prevents water and mud from entering the engine bay through the mask opening, protecting electrical components.
The RFID electronic tag is a modern identification device used for fleet management and tracking, attached to the front shroud and radiator cover for easy scanning.
This bracket limits the opening angle of the mask on the left side, preventing damage to the hinges and bodywork. It is a direct counterpart to the right assembly.
The Left trim panel is a decorative cover that finishes the side of the mask, hiding mounting bolts and providing a clean appearance.
Symmetrical with the left, this panel completes the side trim of the front shroud and radiator cover, ensuring a uniform look.
Our front shroud and radiator cover components are manufactured to Sinotruk’s original specifications, guaranteeing a perfect fit on the HOWO 7. Every panel, hinge, and fastener matches the factory design, ensuring seamless installation.
The mask, nets, and protection bar shield the radiator and engine bay from stones, mud, and impacts. The water fender and wind hoods also improve cooling efficiency, keeping the engine at optimal temperature.
We supply every washer, bolt, nut, clip, and rivet needed for a full front shroud and radiator cover replacement. No additional parts are required, saving time and ensuring a professional repair.
All components are made from high‑quality materials with anti‑corrosion coatings or UV‑stable plastics. The front shroud and radiator cover is built to withstand harsh outdoor conditions, maintaining its appearance and function for years.
The front shroud and radiator cover assembly is the defining visual element of the HOWO 7’s front end, while also serving critical functional roles in cooling, protection, and aerodynamics. This comprehensive kit includes every component needed to fully restore or upgrade the front mask and surrounding trim to factory condition.
The main radiator mask is the centrepiece, available in a high‑position design with integrated grille nets that allow maximum airflow while protecting the radiator from debris. The mask skeleton provides the structural backbone, ensuring that the mask retains its shape and rigidity.
The left and right wind hoods and side screens channel air through the radiator, improving cooling efficiency. The water fender prevents splash‑up from the road, protecting sensitive electrical components from moisture damage.
Hinges and lock assemblies are precision‑engineered for smooth operation and secure closure. The left and right hinge welding assemblies are made from heavy‑gauge steel, and the lock assemblies include spring‑loaded latches that hold the mask firmly in place. The drawstring allows the driver to release the lock from inside the cab.
The trim panels and covers – both interior and exterior – provide a finished look and protect the hinge mechanisms from dirt and moisture. The A‑column trim panels and fixing clips ensure a snug fit without rattles.
All fasteners are supplied in the correct quantities and grades. The big washers, small washers, spring washers, and flange nuts and bolts are tailored to each mounting point. The self‑tapping screws and plastic rivets make installation of trim panels quick and secure.
The circular buffer blocks and spacer rings are critical for alignment and damping, ensuring that the mask does not vibrate or rub against the bodywork. The protection bars add an extra layer of safety in minor collisions.
The RFID electronic tag is a modern addition for fleet management, allowing easy identification and tracking of the vehicle. The plated silver SNOTRUK emblem adds a premium finish, reflecting the quality of the brand.
Replacing the entire front shroud and radiator cover with our genuine kit is a cost‑effective way to refresh the truck’s appearance and ensure that all components are in perfect working order. Over time, plastic parts can become brittle or faded, and hinges can wear out. This kit provides a complete overhaul.
Installation is manageable with basic hand tools and can be completed in a few hours. The components are clearly labelled, and the mounting points are pre‑drilled, so no cutting or welding is required. A torque wrench is recommended for the critical bolts.
For fleet operators, standardising on this genuine front shroud and radiator cover kit ensures consistent quality and appearance across the fleet. The durable materials and corrosion‑resistant coatings reduce the frequency of replacements, lowering the total cost of ownership.
We recommend that the front shroud and radiator cover be inspected regularly for signs of damage, loose fasteners, or deteriorated seals. Replacing worn components with our genuine parts maintains the vehicle’s safety and appearance.
We back our front shroud and radiator cover kit with a 12‑month warranty against manufacturing defects. Our technical support team is available to assist with any installation or compatibility questions.
We ship worldwide with tracking. Expedited shipping is available for urgent orders. Use the Send Email or Get Quotation buttons to request a customised quote for your fleet.
Choosing a genuine front shroud and radiator cover ensures that your HOWO 7 maintains its original styling and protection. Aftermarket alternatives may not have the same fit, durability, or aesthetic quality.
The gas spring support bolts and the drawstring are often overlooked but are essential for daily operation. Our kit includes these items, ensuring that the mask opens and closes smoothly.
The protection bars and limit block brackets are important safety features that prevent over‑opening and protect the radiator in the event of an impact. We supply both left and right assemblies.
We are committed to providing the highest quality components and exceptional customer service. Choose our front shroud and radiator cover kit for peace of mind.
Don’t compromise on front‑end appearance or protection. Replace your damaged or worn components with our genuine kit and enjoy the confidence that comes with a fully tested, factory‑fresh front shroud and radiator cover.
We maintain a large stock to ensure fast dispatch, even for bulk orders. Contact our sales team for volume pricing and customised logistics solutions.
Thank you for considering our front shroud and radiator cover for your HOWO 7 dump truck. We are confident that our genuine OEM product will deliver the reliability and performance you expect from Sinotruk.
The front shroud and radiator cover is a key element of the vehicle’s identity and functionality. Investing in genuine parts ensures that your truck remains safe, attractive, and reliable for the long term.
We provide a comprehensive installation guide with torque specifications and clear diagrams. The kit is designed for easy replacement, with all components clearly labelled for identification.
We are committed to helping you maintain your HOWO 7 in peak condition. Our technical helpline is staffed by engineers with deep knowledge of the body and trim systems.
With proper installation and regular inspection, this front shroud and radiator cover kit will provide years of dependable service, keeping your truck looking and performing its best.
Upgrade your HOWO 7 with the genuine front shroud and radiator cover – the smart choice for protection, style, and long‑term value.
We are proud to be a trusted supplier of OEM Sinotruk parts. Contact us today to order your front shroud and radiator cover and experience the quality that only genuine components can deliver.
Don’t wait until a damaged mask or broken hinge affects your truck’s appearance and safety. Replace your aging components with our genuine kit and enjoy the peace of mind that comes with a fully tested, factory‑fresh solution.
We are here to support your fleet’s needs with fast shipping and competitive pricing. Use the buttons above to request a quote or place your order.
The front shroud and radiator cover is an essential part of your truck’s front-end system. Choose genuine Sinotruk parts for the best results.
We are confident that our genuine front shroud and radiator cover will exceed your expectations. Order today and keep your HOWO 7 looking and functioning at its best.
We are proud to offer this high‑quality front shroud and radiator cover kit, which includes every component needed for a complete front‑end makeover. It is the most comprehensive solution available for the HOWO 7 dump truck.
Our front shroud and radiator cover components are built to meet the highest standards of quality and durability. You can trust them to perform when you need them most.
We look forward to serving your HOWO 7 needs. Thank you for choosing our genuine parts for your vehicle.
We are committed to providing the best service and quality. Trust our front shroud and radiator cover to deliver the performance you expect.
Order now and ensure your truck is equipped with the best front‑end assembly available. We are here to support you every step of the way.
Our online catalog provides comprehensive access to genuine SINOTRUK parts for all major vehicle lines — including HOWO, Sitrak, Steyr, and Yellow River series trucks. You can browse detailed specifications, original part numbers, and exploded-view diagrams for every assembly. Whether you are performing routine maintenance or planning a major overhaul, the catalog helps you quickly identify the correct components for your vehicle. When you become a SINOTRUK customer, we offer complimentary full‑access catalog services, ensuring you always have the latest product data and interchangeability information at your fingertips to support efficient fleet management and accurate parts ordering.
We are a heavy-duty truck parts store. Please leave your contact information and inquiries. We will respond within 12 hours.
