The part is a dedicated accessory for the HOWO MAX 4X2 tractor, providing a blind-hole cover for the front camera mounting point and all necessary fasteners for secure installation. This 360 Loop Front Camer kit ensures that the front camera port is properly sealed when not in use, or that the camera can be mounted reliably. When you choose authentic Howo Parts, this 360 Loop Front Camer guarantees OE fitment and protection for the vehicle’s front camera system. Below are detailed descriptions of every component included with this 360 Loop Front Camer assembly.
The 360 round view front camera blind hole blocking is a precisely moulded plastic or rubber cap that seals the front camera mounting hole on the HOWO MAX cab. This 360 Loop Front Camer cover prevents dust, moisture, and debris from entering the camera opening when the front camera is not installed. The cap is designed to match the contour of the front grille or bumper, providing a flush and aesthetically pleasing appearance.
It is made from UV-stabilised ABS plastic with a matte black finish that resists fading and cracking. The blind hole blocking also helps maintain the aerodynamics of the front end and reduces wind noise. When the optional front camera is later retrofitted, this 360 Loop Front Camer cover can be easily removed and reused elsewhere. The snap-fit design allows tool-less installation and removal, making it a practical solution for fleet operators who may switch camera configurations.
Using the genuine 360 Loop Front Camer blind hole blocking ensures that the front opening remains perfectly sealed, protecting the electrical connector from corrosion and damage. A missing or damaged cover can allow moisture to enter the camera harness, causing short circuits or intermittent camera faults. For vehicles that are operated in dusty or rainy environments, this 360 Loop Front Camer component is essential for preserving the integrity of the front camera system.
This assembly consists of a cross-recessed pan head screw, a spring washer, and a large flat washer, pre-assembled for convenient installation of The part cover or camera bracket. The screw is made from zinc-plated steel with a cross-recessed (Phillips) drive, offering excellent corrosion resistance and easy engagement with standard screwdrivers. The spring washer provides preload to prevent loosening under vibration, while the large washer distributes clamping force over a wider area, preventing the plastic cover from cracking. This 360 Loop Front Camer fastener assembly is referenced as Q2140620 and is used in pairs to secure the blind hole blocking cover. The screw has a thread size of M6 and a length of approximately 20mm,
suitable for the thickness of the cab panel and the cover flange. Proper torque (around 6-8 Nm) ensures a firm seal without over-compressing the plastic. Using the correct 360 Loop Front Camer screw assembly is critical; an incorrect screw may have the wrong length or head type, potentially damaging the cover or not providing enough clamping force. The spring washer and big washer are matched to the screw for optimal performance. This 360 Loop Front Camer hardware set is also used in other front-facing accessory installations, making it a versatile component for the HOWO MAX cab.
360 Loop Front Camer – genuine HOWO front camera blind hole cover and fastener kit for MAX 4X2
The part blind hole blocking provides a watertight and dustproof seal for the front camera opening. This 360 Loop Front Camer cover ensures that the harness connector remains clean and dry, preventing intermittent electrical issues that can affect the camera system.
The included screw, spring washer, and big washer assembly is zinc-plated to resist rust. This 360 Loop Front Camer hardware provides secure and vibration-proof fastening, maintaining the cover in place under harsh road conditions.
The part cover is made from UV-stabilised ABS plastic that resists fading and cracking from prolonged sun exposure. This ensures The part maintains its original appearance and fitment over the life of the vehicle.
This 360 Loop Front Camer kit is manufactured to the exact dimensions of the HOWO MAX front camera mounting hole. The cover snaps in perfectly, and the screw holes align with the factory bosses, making installation quick and tool-free.
The part system on the HOWO MAX 4X2 consists of multiple cameras around the vehicle, including a front-facing camera that provides a view of the area ahead of the bumper. The front camera is normally mounted in a dedicated recess on the front grille, protected by a cover when not in use. The part blind hole blocking cover serves as the factory cover for vehicles not equipped with the front camera, sealing the mounting hole and protecting the electrical connector.
When the camera is retrofitted, this cover is removed and replaced by the camera unit, using the same mounting screws and washers. The part cover is designed to be reusable; it can be stored and reinstalled if the camera is ever removed. The cross-recessed pan head screw assembly ensures that both the cover and the camera are held firmly, preventing any movement that could cause rattling or misalignment. A properly sealed 360 Loop Front Camer cover prevents moisture ingress that could lead to connector corrosion, which is a common cause of intermittent camera faults. Regular inspection of The part cover is recommended to ensure it remains securely attached, especially after driving through heavy rain or washing the vehicle.
Before installing The part cover, clean the camera mounting hole on the front grille or bumper. Remove any debris or old adhesive. Position the blind hole blocking cover over the opening, aligning the snap-fit tabs with the corresponding slots. Press the cover firmly until it clicks into place. For vehicles where the cover is secured by screws,
place the big washer over the screw, then the spring washer, and insert the screw through the cover into the threaded boss. Tighten the screw to 6-8 Nm using a Phillips screwdriver. Do not overtighten, as this could crack the plastic cover. If the vehicle is being retrofitted with a front camera, remove the cover and store it in a clean, dry location. Install the camera using the same screw assembly, ensuring the camera is correctly oriented and securely fastened. Test the camera function after installation. The part cover installation is now complete.
If The part cover becomes loose or falls off, the snap-fit tabs may be broken or the screws may have loosened. Inspect the cover for damage and replace it with a new 360 Loop Front Camer cover if necessary. If the screws are loose, retighten them to 6-8 Nm. If the cover does not sit flush, check for debris in the mounting hole.
If the camera (when fitted) does not produce an image, the connector inside the mounting hole may be corroded due to a missing or damaged cover; replace the cover immediately. A rattling sound from the front area may indicate a loose 360 Loop Front Camer cover; tighten the screws. Always use genuine 360 Loop Front Camer components to ensure correct fitment and sealing.
The part cover requires minimal maintenance, but it should be inspected regularly, especially after off-road use or high-pressure washing. Check that the cover is securely attached and that the screws are tight. If the vehicle is subjected to harsh environments, the screws may corrode; replace them with new 360 Loop Front Camer screw assemblies if rust is visible.
The cover itself should be wiped clean with a soft cloth and mild detergent to remove dirt and grime. If the vehicle is in a region with extreme sunlight, periodically inspect the cover for signs of fading or brittleness; replace it if it becomes cracked or deformed. For fleet operators, keeping a spare 360 Loop Front Camer cover in the parts inventory can minimise downtime if a cover is lost or damaged.
This 360 Loop Front Camer kit is specifically designed for the HOWO MAX 4X2 tractor cab, fitting all production years from 2018 onward. The blind hole blocking cover is compatible with the front camera mounting recess on both standard and high-roof cabs. The part kit is also compatible with SITRAK C7H and HOWO T7H models that share the same front grille design. It is not compatible with older HOWO A7 or WD615 cab versions, which use a different camera mounting hole size.
The screw assembly (Q2140620) is a standard M6 screw assembly used in many parts of the HOWO MAX cab, making this 360 Loop Front Camer kit useful for other applications where similar fasteners are required. Always verify your vehicle’s cab type and production year before ordering this 360 Loop Front Camer kit.
Aftermarket blind hole covers may not fit properly, allowing moisture and dirt to enter the camera connector, causing short circuits and expensive camera replacements. Generic screws may have the wrong thread pitch or length, damaging the plastic mounting bosses. The spring washers in copy kits may not provide adequate tension, causing the cover to loosen and fall off.
Genuine HOWO 360 Loop Front Camer components are manufactured to SINOTRUK’s exact specifications, using UV-stable plastic, precision-formed snap-fit tabs, and high-quality zinc-plated fasteners. The small additional cost of a genuine 360 Loop Front Camer kit is insignificant compared to the cost of replacing a damaged front camera or the labour involved in diagnosing intermittent electrical faults.
We are a heavy-duty truck parts store. Please leave your contact information and inquiries. We will respond within 12 hours.
