

The WG9525950666 Right Rear Wheel Cover Bracket is a precision‑engineered structural component that securely anchors the right rear wheel cover to the chassis, preventing vibration, rattling, and premature wear of the fender assembly. Manufactured from high‑strength steel with a durable anti‑corrosion coating, this bracket delivers exceptional rigidity and long‑term reliability in the most demanding operating conditions. As a genuine part of Howo/Sitrak truck parts, the WG9525950666 is produced to exact OEM specifications, guaranteeing a perfect fit and superior performance in HOWO, SITRAK, and SHACMAN heavy‑duty trucks. Whether you are replacing a bent or corroded bracket after a minor collision or restoring proper wheel cover alignment during a chassis repair, this component provides the strength, precision, and durability required to keep your truck looking sharp and operating safely.
The WG9525950666 is not a simple stamped strip; it is a precision‑engineered bracket that combines advanced material selection with exacting manufacturing tolerances. Manufactured from high‑grade cold‑rolled steel, this bracket provides an optimal balance of tensile strength, toughness, and fatigue resistance, ensuring that it can withstand the constant vibration and occasional impacts that heavy‑duty trucks endure. The bracket’s geometry is carefully designed to distribute load evenly across the mounting points, preventing stress concentration and protecting the wheel cover and chassis from deformation. Its mounting holes are precisely positioned and drilled to match the OEM pattern, guaranteeing a secure, rattle‑free installation without the need for drilling or modification.
The bracket is finished with a durable zinc‑plated coating that provides excellent corrosion resistance, protecting it from road salt, moisture, and debris. The edges are deburred and chamfered to facilitate handling and prevent damage to surrounding components. Every WG9525950666 is inspected for dimensional accuracy, hole alignment, flatness, and surface finish, ensuring that it meets the strictest OEM standards. This attention to detail guarantees that the right rear wheel cover bracket performs flawlessly, maintaining proper cover alignment and structural integrity over hundreds of thousands of kilometers. Whether your truck operates in construction, mining, or long‑haul applications, this bracket delivers the reliability you need.
High‑Strength Steel – The cold‑rolled steel construction of the WG9525950666 provides exceptional rigidity, preventing bending and ensuring stable wheel cover support under all conditions.
Precision Fit – The mounting holes and overall dimensions are manufactured to exact OEM tolerances, ensuring a perfect fit and proper cover alignment.
Corrosion Resistance – The zinc‑plated finish protects the bracket from rust and environmental corrosion, ensuring long‑term durability and easy removal.
Vibration Damping – The bracket’s rigid design and secure mounting reduce vibration transfer, minimizing wear on the wheel cover and fender assembly.
The WG9525950666 right rear wheel cover bracket is dimensionally identical to the original equipment part used across a wide range of HOWO, SITRAK, and SHACMAN heavy‑duty trucks. It is specifically designed for the HOWO NX, T5G, T7H, and TX series, as well as compatible SITRAK C7H and G7 models. The bracket’s mounting holes, overall length, thickness, and bend angles match the OEM specifications exactly, ensuring a seamless replacement that requires no drilling, cutting, or modification. By choosing this genuine component, you avoid the risks associated with aftermarket brackets that may have incorrect dimensions, poor material quality, or inadequate corrosion protection, which can lead to cover misalignment, rattles, and premature failure.
The WG9525950666 has been validated through extensive vibration and durability testing, confirming its ability to maintain structural integrity and proper cover alignment over hundreds of thousands of kilometers. Fleets that have standardized on this right rear wheel cover bracket report fewer chassis‑related complaints, improved vehicle appearance, and reduced maintenance costs. Its robust construction ensures dependable service in the harshest operating environments, from dusty construction sites to rainy and snowy highways. The bracket is also compatible with standard mounting hardware, making it a versatile choice for a wide range of repair and restoration projects.
Installing the WG9525950666 right rear wheel cover bracket is a straightforward process that can be completed with basic hand tools. Begin by disconnecting the negative battery terminal for safety and supporting the wheel cover with a jack or stands to relieve tension on the mounting points. Carefully remove the old bracket by loosening and removing the mounting bolts. Take note of the fastener locations and any shims or spacers that may be present. Clean the mounting surfaces on the chassis and cover thoroughly, removing all dirt, rust, and old thread‑locking compound. Inspect the chassis and cover for any damage; if any is found, repair it before proceeding.
Position the new WG9525950666 bracket onto the chassis, aligning the mounting holes with the corresponding threaded inserts. Hand‑start all bolts to ensure proper alignment, then tighten them evenly in a sequential pattern to the manufacturer’s recommended torque. Avoid over‑tightening, as this can distort the bracket or strip the threads. Reconnect the battery and lower the cover, checking that it sits level and aligns properly with the fender and body panels. Test the bracket for rigidity by gently pushing and pulling on the cover; if any movement is detected, re‑check the bolt torque and bracket alignment. For maintenance, periodically inspect the bracket for signs of corrosion, cracking, or loose fasteners during routine service. With proper installation and care, the WG9525950666 will provide reliable wheel cover support and a professional appearance for years.
Each WG9525950666 right rear wheel cover bracket is manufactured in an ISO 9001‑certified facility, following strict process controls from raw material to finished product. The cold‑rolled steel is tested for thickness, tensile strength, and chemical composition before stamping. The progressive die tooling ensures consistent geometry and dimensional accuracy across every production run. After forming, each bracket is deburred and then zinc‑plated for corrosion protection. A 100% visual inspection is performed to detect surface defects, cracks, or incomplete coating.
Random samples from each batch are subjected to dimensional inspection, hardness testing, and salt‑spray corrosion testing to confirm compliance with OEM standards. A fitment test is performed on a master chassis buck to ensure proper alignment with the cover and chassis mounting points. This comprehensive quality assurance guarantees that every WG9525950666 delivers the same reliable performance as the original OEM component, giving you full confidence in your replacement.
Fleet managers and technicians consistently choose the WG9525950666 because it delivers reliable wheel cover support and long‑term durability at a competitive price. The bracket’s precise fit and high‑quality zinc‑plated finish eliminate common problems such as misalignment, corrosion, and vibration that are often associated with cheaper aftermarket parts. Many workshops report a significant reduction in chassis‑related complaints after installing this genuine OEM bracket, and drivers appreciate the secure, rattle‑free wheel cover that reflects well on the fleet. The WG9525950666 is also supplied in robust packaging that protects the bracket during transport and storage, and its clear OEM number simplifies parts identification.
Moreover, the WG9525950666 is backed by a comprehensive quality guarantee and is supported by our technical team. Its availability through our distribution network ensures fast delivery when you need it most. When you choose this right rear wheel cover bracket, you are selecting a component that has been engineered and tested to the highest standards, offering the perfect balance of strength, precision, and value. Keep your truck looking sharp and protected with the WG9525950666.
In summary, the WG9525950666 Right Rear Wheel Cover Bracket is a premium replacement component that restores your truck’s wheel cover alignment while providing essential structural support for the fender assembly. Its exact OEM fitment, high‑strength steel construction, and corrosion‑resistant finish ensure that it meets the demanding requirements of heavy‑duty operation. By investing in this genuine replacement part, you are enhancing the safety, reliability, and appearance of your HOWO, SITRAK, or SHACMAN truck, all while reducing overall maintenance costs.
Don’t compromise on wheel cover integrity or style – choose the WG9525950666 for your next bracket replacement. With its proven track record and widespread acceptance among professionals, this right rear wheel cover bracket is the smart choice for anyone who values quality, durability, and peace of mind. Keep your truck looking its best and running protected with the WG9525950666 – the definitive choice for HOWO and SITRAK professionals.